Welcome to the Qinsun Instruments Co., LTD! Set to the home page | Collect this site
The service hotline

Search


Related Articles

Product Photo

Contact Us

Qinsun Instruments Co., LTD!
Address:NO.258 Banting Road., Jiuting Town, Songjiang District, Shanghai
Tel:021-67801892
Phone:13671843966
E-mail:info@standard-groups.com
Web:http://www.qinsun-lab.com

Your location: Home > Related Articles > DIN Abrasion Tester-GB9867 Rubber Roller Abrasion Testing Machine

DIN Abrasion Tester-GB9867 Rubber Roller Abrasion Testing Machine

Author:QINSUN Released in:2023-04 Click:113

DIN Abrasion Tester-GB9867 Rubber Roller Abrasion Tester The main principle is that under a certain load, at a certain level of mesh, the columnar sample cross-cut and ground on the mesh surface for a given stroke. By measuring the mass wear of the sample, the volume wear is calculated from the density of the sample. To make the test comparable, a standard rubber should be used in the end. , express the test results as the relative volume wear based on the calibrated mesh or wear resistant base expressed as the wear resistance of a given standard rubber.

Product introduction

DIN Abrasion Tester-GB9867 Rubber Roller Abrasion Tester suitable for elastic materials, rubber, tires, conveyor belts, soles, soft synthetic leather. . . The wear measurement of other materials has the knowbrands of high performance, good reproducibility and easy operation. The main principle is that under a certain load, at a certain level of mesh, the columnar sample is ground and ground for a certain impact on the surface of the mesh, and the mass abrasion of the sample is measured, and then calculated from the density of the sample Volume wear, in order to make the test comparable, the standard rubber should ultimately be used, and the test result is expressed as the relative volume wear based on the calibrated mesh or fully expressed as the wear against a certain standard rubber wear-resistant base.

Standard:

DIN 53516, JIS K6369, GB/T 20991 No. 8.3, GB 20265-2006 , GB20266-2006, SATRA TM174, BS 903, JIS K6264, GB/T9867, ISO4649, etc.

Features:

Roller wear machine is also called DIN wear resistant instcalled rument-GB9867 rubber roller abrasion tester, used to measure the abrasion resistance of rubber tires, rubber shoes, tapes, etc. to identify rubber The quality of the product. During the test, the rubber material rubs against the mesh on the roller under a certain load and the wear of the sample is measured within the specified stroke. Meet the requirements of GB9867, ISO4649 and DIN53516. The machine has the advantages of small sample size, time saving, non-repetitive friction path and low noise.

Specifications:

Test piece: φ16mm, 6~15mm (D)

Load armature: 2.5N

Weight load: 2.5N, 5N

Side displacement clamp: 4.2mm/roller per circle

Abrasive cloth: 60#

Roller diameter: 150 mm

Roller length: 460 mm

Roller speed: 40 rpm

Route schedule: 40 m /20m

Sanding speed: 0.32 m/sec

Inclination angle: 3°The angle between dthe supporting axis of the test piece and the vertical surface of the roll

p>Volume: 70×30 ×30cm

Weight: 61kg

Nutrition: 1∮, AC220V, 3A

st melting>Standard configuration:

2 sheets of P60# standard sandpaper, 1 standard die, 5 standard test pieces, 1 aluminum block, 1 brush and 1 small bench drill.

Product details:

Put the sample on a specific carrier medium and place it on a rotating drum wrapped in standard sandpaper. The operator records the weight of the sample before and after the test to detect the weight loss and uses this value to calculate the abrasion resistance via the standard formula.

Note: For general use, please purchase a specific gravity balance

Prev:

Next: