Welcome to the Qinsun Instruments Co., LTD! Set to the home page | Collect this site
The service hotline


Related Articles

Product Photo

Contact Us

Qinsun Instruments Co., LTD!
Address:NO.258 Banting Road., Jiuting Town, Songjiang District, Shanghai

Your location: Home > Related Articles > YG401F Martindale Wear Tester (9 Stations) High Quality

YG401F Martindale Wear Tester (9 Stations) High Quality

Author:QINSUN Released in:2023-02 Click:147

YG401F Martindale Abrasion Tester (9 stations)


It is used to test the wear resistance and degree of pilling of knitwear, woolen fabric, imitation leather, faux leather, etc. under pressure.

【Standard Conformity】

GB/T4802.1-1997, ASTM D4970, ISO12945-2:2002, JIS 1096E, ISO12947 etc.

【Technical parameters and configuration】

★The number of stations: 9 or 8

★Count display:

a. Estimated number: 0~999999 times

b. Accumulated number: 0~999999 times

Stroke: 24±0.5mm, 60.5±0.5mm

★Print quality:

a. Holder: 200 ± 1g

b. Sample weight: Fabric sample weight: 395 ± 2g

Furniture decoration sample weight: 594 ± 2g

C. Stainless steel flap: 260 ± 1g

Grinding block effective friction diameter:

Type A 200 g (1.96 N) friction head ¢28.8-0.084 mm

B type 155g (1.52 N) Friction head ¢90-0.10 mm

★ Clip Relative speed of movement between holder and grinding table: 50-2r/ min

★Mass of loading hammer: 2385± 10g

★Dimensions: 885×600×410mm (L×W×H)

★Weight: 150kg

★Power supply: AC220V 50Hz

How to Purchase a Qualified Martindale Abrasion Tester Extended Reading:

The Martindale Abrasion Tester is used to measure fabric pilling under light pressure. Under the specified load, the circular sample is rubbed with the abrasive material (ie, standard fabric) with the planar motion of the trajectory forming the Lissajous figure. The sample holder containing the sample or abrasive is free to rotate about its axis perpendicular to the horizontal plane. Whether the sample holder is filled with the sample or the abrasive depends on the test method used. Its trajectory forms a planar frictional motion of a complete Lissajous figure, including 16-fold friction, ie the two outer drive wheels of the Martindale wear tester rotate 16 times and the inner drive wheel rotates 15 times. The Lissajous figure prescribed in the standard is a figure formed by alternating movements. from a circle to gradually narrowThe flattened ellipse until it becomes a straight line, from which it asymptotically passes again into an expanded ellipse to a circle, repeating the movement diagonally. However, the instruments manufactured by many domestic small businesses without production qualifications and processing techniques do not have the standard Lissajous gauge at all, leading to uncertainties in the test results. (See image below)

Default Lissaru graphics motion trajectory.

Remove the material from the grinding table, cover the surface of each grinding table with ordinary white paper with a diameter of (100±5) mm and a basis weight of at least 100 g/m2 and fix it on the sanding table Make sure the surface is perfectly flat.

Insert the stainless steel sleeve with the same diameter as the sample pin shank into the shank sleeve of the sample guide plate in turn, install an ordinary ballpoint pen and bring the pen tip into contact with the surface of paper. Rotate the instrument so that the number of rubs is 16 times to form a complete Lissajous figure.

Draw two parallel lines that just meet the extreme curves on opposite sides of the Lissajous figure. Draw two more parallel lines for the other two sides, making sure the lines intersect perpendicularly. Measure with an accuracy of ±0.2 mm on each side using an appropriate method. Check the 31 lines drawn, it is important to check the symmetry of the Lissajous figure. If the curves match or the paratand is uneven (see Figure A.1), consult the equipment supplier designed, its appearance is beautiful and generous, it adopts a touch screen, the interface is easy to understand, and it is easy to operate. The microcomputer system uses two counting methods , which are intuitive and easy to set. Test at the same time to improve test efficiency. The instrument is also equipped with two types of Lissajous (Lissajous) 24mm × 24mm, 60.5mm × 60.5mm movement track and various supporting accessories, which can be adapted to different test methods and standards.

This instrument is suitable for testing the degree of pilling of fabrics, such as GB/T4802.2, ASTM D4970, ISO12945-2, etc. The principle: Under specified pressure, the circular sample is filled with the fabric of the same Material rubbed according to the path of the Lissajous figure and after reaching the specified number of revolutions of theDegree of pilling of the sample evaluated. It is also suitable for abrasion resistance test of GB/T13775, ASTM D4966, ISO12947 and other fabrics. Its principle: under a certain pressure, the circular fabric sample will rub against the standard abrasive according to the movement trajectory of the Lissajous curve, causing damage to the sample, and the wear resistance of the fabric is expressed by the number of samples is damaged performance.

【Related wear-resistant pilling products】

Box-type pilling process (2 boxes)----YG(B)511-II roller pilling- Boxed Tester

Boxed Pilling Tester (4 Boxes)----YG(B)511-IV Boxed Rolling Pilling Tester

Martindale Method (8 resp 9 digits)---YG(B)401E Martindale Abrasion Tester

Martindale Method (4 or 6 positions)---??YG401G Martindale Abrasion Tester (4 positions)

Circle Track Method--YG(B)502 Fabric Pilling Tester

Abrasion Test by Abrasive Wheel Method - YG(B)522 Abrasion Testing Machine (TBUT abrasion)


Martindale surface grinder fabric surface grinder digital fabric surface grinder Martindale Wear Tester Fabric Wear Tester