FLR-002 ring compression strength tester

Product introduction

This machine is equipped with various fixture accessories to test the ring compressive strength of the base paper, cardboard Flat compressive strength, edge compressive strength, adhesive strength and other tests, so that paper product manufacturers can control production costs and improve product quality.

The performance parameters and technical indicators of the products comply with the following standards: GB/T 2679.8 \"Determination of ring crush strength of paper and board\", GB/T 6546-1998 \"Corrugated Board Edge Crush standards such as \"Determination of Strength\", GB/T 6548-1998 \"Determination of Bonding Strength of Corrugated Board\", GB/T 2679.6-1996 \"Determination of Flat Compression Strength of Corrugated Board\" and other standards

can perform tests:

1.Equipped with a ring pressure test center disk and a special ring pressure sampler to perform a cardboard ring compression test (RCT) to perform;

2. Equipped with side pressure (sticky

3. Equipped with a peel strength test bench for corrugated board adhesion (peel) strength test (PAT) ;

4. Equipped

Ring Compressive Strength Tester Product Advantages:

1.The system automatically calculates the ring compressive strength and side compressive strength without manual calculation by the user, reducing the workload and errors;</p

2. Comes with packaging stacking function, which can set the force and time directly, then stop automatically after the test is completed;

3. After the test is completed, is there an automatic return function, which automatically judges the breaking force and automatically saves the test data;

4 .Three speeds can be set, all Chinese LCD display operating interfaces, a variety of units to choose from;

5. Can record and save test results 20 times.

Ring compression strength testerTechnical parameters:

Parameter type

Technical specification

Model

Model

p>

FLR-002 Ring Compression Strength Tester (LCD)

Capacity

Optional within 200kg

Display mode

High- definition LCD screen display, digital A/D value input speed 100 times/s, high test accuracy

Unit switching

N , kN, kgf, gf, lbf

Test Speed

12.5 ± 2.5 mm/min

Test Accuracy

±1%

Resolution

1/10000

Plate parallelism

≤0.05mm

Standard plate

100X100mm

Size

360*330*550mm

Weight

60kg

Print

Micro thermal printer

Power supply

AC220V

Standard configuration

A few fixtures

Optional configuration

Parallel sampler; ring pressure sampler, ring pressure fixture; flat pressure fixture; adhesive strength fixture

Product properties:

1.32 bit embeddedd Type of processing chip, fast instruction cycle;

2. Voltage measurement accuracy > 4 gears, i.e. resolution > 20000 meters;

3. Use software coefficients to calibrate (correct) files. Effectively correct the linearity of the sensor;

4. 4.4 times the frequency of the photoelectric encoder positive and negative bidirectional counting, high resolution;

5. The display uses a large 192×64 dot matrix monochrome LCD screen, which can display more information;

6. 1 RS232 serial port, which can be connected to other devices;

7 ．1 parallel print port, which can be connected to a micro printer or dot matrix printer;

8. 8 control buttons (5 function keys, 3 multiplex keys), easy to operate; </p

9. Unit of force: N, kN, kgf, gf, lbf;

10. Tension unit: Pa, kPa, MPa, kgf/cm2, lbf/in2;

11. Length (area) unit: mm, cm, in;

12. Ingait function: two-way simulation signal;

13. Display function: the maximum strength during the test can be automatically displayed and memorized at the end of the test;

14. Store output: Up to 20 test results can be recorded.

Environmental conditions for normal use of the instrument:

1. Room temperature: 20℃±10℃;

2. Power supply: AC220V±22V, 50Hz, maximum current 3A, the power supply must be grounded reliably, if the power supply voltage fluctuation exceeds the above range, a power supply voltage stabilizer should be used;

3. The working environment is clean, without strong magnetic fields and vibration sources, and the workbench is flat and stable.

Prev: Test machine against yellowing