Commonly used standards for surface wear resistance of automotive materials.

Common Standards for Surface Wear Resistance of Automotive Materials

Reference Standards

ANSI / SAE Z26.1 - 1996

Safety glass for automobiles and automotive equipment

The purpose of the test is to determine whether the plastic has a certain resistance minimal wear.

ANSI/SAE Z26.1 - 1996

Safety glass for automobiles and motor vehicle equipment

The aim of the test is to determine whether the safety glass has a certain minimum resistance to wear.

ASTM D7255

Standard test method for abrasion resistance of leather (rotating platform, rotary platform method double head)

The test method covers the determination of the abrasion resistance of leather using a rotating double head abrasion tester (RPDH ).

ASTM G195

Standard Guide for Abrasive Testingdual head rotary r

The purpose of this guide is to assist you in performing the procedures for the abrasion test at the rotary double head abrader (RPDH) of rigid or flexible materials

DaimlerChrysler LP - 463KB - 21 - 01

 

Wear Resistance of Decorative Materials-TABER Method

This is a method using a double wheel abrasion tester to determine the resistance to wear of packing materials.

Daimler-Chrysler MS-PP11-1

Vacuum coated plastic parts - surface decoration

This standard introduces the coating system necessary for the vacuum coating of plastic parts, interior parts made of ABS plastic, acrylic fiber, nylon, polycarbonate, butyric acid plastic or other materials.

Daimler-Chrysler MS-PP11-2

Vacuum coating-high wear resistance of plastic parts -decorsurface ation

This standard outlines the coating system required for vacuum coated plastic interior parts that require high wear resistance. These parts may be made of ABS plastic or elastic butyrate or other specified materials.

Daimler-Chrysler MS-JP4-13

Car mats

Ford ESB-M99P14-A1 Engineering Material Specification

Pad printing, plastic or plastic head painted, interior parts

Transfer printing referred to in this specification is the transfer of the ink system onto the surface of interior plastic parts through a process pad printing. They were originally released for transfer inks intended for graphics on interior plastic parts.

Ford WSS-M15P34-B1 Engineering Material Specification

This specification was originally developed for stickers used on dashboards and interior door trims. Continuous contact parts must have high wear resistance, such as door panels, game consoles, radios or other control settings.

Ford WSS-M15P34-B2 engineering materials specifications

Performance, interior decorative stickers, low wear

 

This specification was originally developed for stickers used on dashboards. and interior door trim. Wear resistance requirements are low for locations that are not continually contacted by users, such as the rear of the steering column or vertical dashboard surfaces that are not close to the buttons.

Material SpecificationsFord WSS-M15P4-E Engineering

Performance specifications for interior assemblies

 

This specification defines the minimum requirements for durability and performance required for decorative and/or functional interior panels and trim panels composed of various combinations of materials.

Ford Laboratory Test Method BN 108-02

Wear Resistance - Taber Abrasion Meter

 

This application allows you to test textile fabrics, coated fabrics, real leather, cardboard, rubber floor mats, carpets, coverings, materials, plastics and othersIts floor paints the wear resistance of the substrate.

Ford laboratory test method BN 108-04

Scratch resistance

  This procedure is used to determine the scratch resistance of materials such as painted substrates, painted plastics, leatherand luggage compartment mats.

General Motors GM2751

Car interior fabrics

This specifications describe interior fabrics for seat covers, door trim and other applications. The fabric is made of fibrous textile materials and is knitted, woven or otherwise. The specifications also include a moldable fabric construction.

General Motors GM9515P

Abrasion resistance of organic coating (Taber abrasion resistance test)

This test method is modified from ASTM D4060 and outlines the steps for determining the abrasion resistance of organic coatings using the TABER abrasion method.

General Motors GM9911P

Wear resistance of plastic coatings

This method is used to determine the resistance of a coating to peeling from the substrate.t.

General Motors GMW3208

Rotational wear test, Taber type

This standard determines the wear resistance of materials using a rotating abrasion measuring device. [Note: This standard is intended to equate or replace methods used to test fabric materials. ]

General Motors HN0245

Wear resistance measurement

Hyundai/Kia MS 300-2

Abrasion resistance of automobile interior decoration and knitted fabrics

ISO 3537

Road vehicles - Safety glass materials - Mechanical tests

This standard specifies mechanical test methods for safety requirements related to all automotive safety glazing, covering all types, regardless of their material or composition.

SAE J 1530

Test method for determinationfiber optic shedding resistance, abrasion resistance and whiskering of automotive carpet materials

This test method covers the determination of fiber shedding resistance, abrasion resistance and whiskering of automotive carpet materials.

SAE J 1847

Wear resistance test - automotive exterior pattern

 This SAE recommended practice applies to trim strips and graphic abrasion resistance testing. It may also feature some vehicle-related labels and wood-grain plastic film. Results are judged by their readability, graphic logo pattern and color.

SAE J 2394

Seven-conductor cable for ABS power

This SAE standard establishes the minimum composition and performance requirements for 7 conductor 1/8-2/10-4/12 cables usedon trucks and trailers.

SAE J 365

Method for testing scratch resistance of trim parts

This test can be used to determine the scratch resistance of fiberboard, fabrics, plastic coated fabrics, leather, etc.

 

SAE J 948

Abrasion resistance testing and entanglement testing of body fabrics, vinyl and Automotive Leather

The Taber test method is used to determine the abrasion and tangle resistance of automotive fabrics and/or vinyl coated fabrics.

SAE J80

Wear resistance of automobile rubber pads

This approach covers the requirements for rubber floor mats, which are made from 5 rubber compounds to meet application needs.

United Nations - ECE Regulation 43

Uniformly stipulates the cCertification of safety glass and glass materials

This regulation applies to safety glass and glass materials which may be used to manufacture windscreens or window panes of motor vehicles, etc.

Prev: Gravel Impact Test and Experimental Exploration of Automobile Body

Next: The sponge indentation hardness test conforms to the standards and requirements of testing procedures.